Lighting-Gallery.net

Advertisements => Wanted => Topic started by: GE101R on March 04, 2019, 12:09:35 PM



Title: Wanted: GE glass refractor for M400
Post by: GE101R on March 04, 2019, 12:09:35 PM
I am looking for a glass refractor for a GE M-400 luminaire. This is a 1950's model with the thin ridge on the glass section that fits into the metal lower hinged base. The lips on the newer globes are too thick for the M-400 to close properly.
The House Side of the glass has the squiggly lines running vertical.


Title: Re: Wanted: GE glass refractor for M400
Post by: wide-lite 1000 on March 08, 2019, 04:59:25 PM
Watch eBay, these occasionally come available and sometimes really cheap ! i bought on last summer for one of my M-400's for like $40.00 with free shipping! If I see any more I'll let you know. GOOD LUCK !!


Title: Re: Wanted: GE glass refractor for M400
Post by: GE101R on March 10, 2019, 02:03:07 PM
Watch eBay, these occasionally come available and sometimes really cheap ! i bought on last summer for one of my M-400's for like $40.00 with free shipping! If I see any more I'll let you know. GOOD LUCK !!

Thanks. It must be the refractor with the thin lip that fits the clam shell.


Title: Re: Wanted: GE glass refractor for M400
Post by: wattMaster on March 10, 2019, 04:05:25 PM
I think I might have one that might work. It goes to a M400A1 from the 1960s and I don't have a use for it right now.


Title: Re: Wanted: GE glass refractor for M400
Post by: GE101R on March 10, 2019, 08:32:50 PM
I tried a M400A-2 glass and the lip was too thick and the door would not close. The M-400 clam shell I have was received with a cracked globe and I found a replacement on Ebay. Looked the same but it did not fit because of the lip.
The original glass had the wavery lines in the rear "house side" section of the glass.

What would you want for it?


Thanks....Steve


Title: Re: Wanted: GE glass refractor for M400
Post by: wattMaster on March 11, 2019, 06:27:16 AM
I would probably want around $10 + shipping, but before it can be sold I have to double check so make sure the lip is thinner than a regular globe, which can't happen until later today.

Also, it can come with a freebie fixture if you want, as it's where the lens came from and I don't have a use for it.


Title: Re: Wanted: GE glass refractor for M400
Post by: wattMaster on March 13, 2019, 12:39:26 PM
I checked my M400 refractors, and they seem to be the same. However, I might measure them with a tape and see if they're actually different.


Title: Re: Wanted: GE glass refractor for M400
Post by: WestinghouseCeramalux on March 20, 2019, 10:23:26 AM
There are two versions of this refractor that I know of. One is made by Holophane, and the other by Pyrex. You need the Pyrex version, which is the original design for the Form 400 and later the M400 series. (The Holophane version showed up in the mid eighties with the redesign M400 series...first saw this in 1984 when I was growing up.) 


Title: Re: Wanted: GE glass refractor for M400
Post by: wide-lite 1000 on March 20, 2019, 03:39:23 PM
I see what your talking about, i just looked at some of my refractors and the one in my form-400 has a 3/16 rib running around the center of where the refractor meets the gasket, the later refractor doesn't have it, it's just a flat surface. Is your light a form-400 clamshell or a M-400 cobrahead ?


Title: Re: Wanted: GE glass refractor for M400
Post by: GE101R on March 25, 2019, 07:40:16 AM
I s what your talking about, i just looked at some of my refractors and the one in my form-400 has a 3/16 rib running around the center of where the refractor meets the gasket, the later refractor doesn't have it, it's just a flat surface. Is your light a form-400 clamshell or a M-400 cobrahead ?

Sorry about the late reply. It is a clam shell. Seems the glass lip is too thick to fit into the slot holders on the metal band with the latch assembly.

Steve


Title: Re: Wanted: GE glass refractor for M400
Post by: GE101R on March 25, 2019, 07:03:28 PM
I think I might have one that might work. It goes to a M400A1 from the 1960s and I don't have a use for it right now.
It is a clam shell and the part of the refractor that fits into the tabs on the latch ring are too thin for a later model glass.


Title: Re: Wanted: GE glass refractor for M400
Post by: wide-lite 1000 on April 29, 2019, 08:02:54 PM
check out the refractor that Memorex/Telex just listed in the "for sale or trade" section, that looks an awful lot like what is in my form 400


Title: Re: Wanted: GE glass refractor for M400
Post by: GE101R on May 05, 2019, 08:26:13 AM
check out the refractor that Memorex/Telex just listed in the "for sale or trade" section, that looks an awful lot like what is in my form 400

Thanks