Author Topic: Why not more POWR/DOOR or PowerPad fixtures  (Read 1655 times)
M250R201SA
Member
*****
Offline

Gender: Male
View Posts
View Gallery


JGriff021985 JMG717
Why not more POWR/DOOR or PowerPad fixtures « on: June 22, 2016, 04:40:16 PM » Author: M250R201SA
Why don't utilities use more M250A2 POWR/DOOR instead of the M250R2?  Wouldn't it be easier to R&R POWR/DOOR luminaires instead of R&R M250R2, M400R3, etc.  Personally, I would us eht M250A2 and M400A3 due to their simplicity to work on.  Price?
Logged

"I know a thing or two about a thing or two...  I sure do."

Ash
Member
*****
Offline

View Posts
View Gallery


Re: Why not more POWR/DOOR or PowerPad fixtures « Reply #1 on: June 22, 2016, 05:41:56 PM » Author: Ash
Its 2 different beancounters choosing the lanterns and paying salary per working hours, so there you get it....
Logged
Silverliner
Administrator
Member
*****
Offline

Gender: Male
View Posts
View Gallery

Rare white reflector


GoL
Re: Why not more POWR/DOOR or PowerPad fixtures « Reply #2 on: June 23, 2016, 01:24:32 AM » Author: Silverliner
It's because single door fixtures are cheaper.
Logged

Administrator of Lighting-Gallery.net. Need help? PM me.

Member of L-G since 2005.

Collector of vintage bulbs, street lights and fluorescent fixtures.

Electrician.

Also a fan of cars, travelling, working out, food, hanging out.

Power company: Southern California Edison.

M250R201SA
Member
*****
Offline

Gender: Male
View Posts
View Gallery


JGriff021985 JMG717
Re: Why not more POWR/DOOR or PowerPad fixtures « Reply #3 on: June 23, 2016, 02:40:32 PM » Author: M250R201SA
So, the single door fixtures are cheaper, and it costs less time to just remove the bad fixture, and replace it with a new one. 

Probably why the Durastar series didn't take off.  It is pretty time consuming compared to installing an M250R2
Logged

"I know a thing or two about a thing or two...  I sure do."

Ash
Member
*****
Offline

View Posts
View Gallery


Re: Why not more POWR/DOOR or PowerPad fixtures « Reply #4 on: June 23, 2016, 03:21:52 PM » Author: Ash
No, it tkes less tim to swap out a gear tray (or door)

But as often things go, somebody specifies the fixtures only based on things "in the scope of his job" under pressure to keep costs down on those things only. So he may well choose a fixture that is 5% cheaper cause that is what he is obligated to do, but would involve 20% higher maintenance costs (and its still a fairly good case) but that are some other department's expenses..
Logged
streetlight98
Member
*****
Offline

Gender: Male
View Posts
View Gallery

Mike McCann


GoL Mike McCann 88219189@N04/albums
WWW
Re: Why not more POWR/DOOR or PowerPad fixtures « Reply #5 on: June 26, 2016, 10:07:22 PM » Author: streetlight98
Around here, the reason they never took off is because the replacement Power/door ballast modules don't cost that much less than never fixtures, and in the eyes of the electric company, street lights depreciate to little value just like how a new car looses half its value the second it's driven off the lot. Once the fixture is installed and used, 10 years later, it's only worth its price in scrap, so they replace it. Who's to say a component won't break down the line and rack up the maintenance expenses? By installing a brand-new light, they can rest safe that the entire fixture is under warranty. A twisted way of thinking, but it all comes down to cost in the end.
Logged

Please check out my newly-updated website! McCann Lighting Company is where my street light collection is displayed in detail.

M250R201SA
Member
*****
Offline

Gender: Male
View Posts
View Gallery


JGriff021985 JMG717
Re: Why not more POWR/DOOR or PowerPad fixtures « Reply #6 on: June 26, 2016, 11:43:47 PM » Author: M250R201SA
@streetlight98...  That does make a lot of sense.  Thanks!!
Logged

"I know a thing or two about a thing or two...  I sure do."

icefoglights
Member
*****
Offline

Gender: Male
View Posts
View Gallery

ITT Low Pressure Sodium NEMA


GoL
Re: Why not more POWR/DOOR or PowerPad fixtures « Reply #7 on: June 30, 2016, 01:04:07 AM » Author: icefoglights
The degree of standardization has a lot to do with it also.  I've noticed Powr/Doors to be most popular with utilities or entities that have fairly standardized lights, so there's a good chance that a replacement door will fit a good majority of fixtures the repairman could be faced with.  Areas with little to no standardization, especially among their larger fixtures, I've almost never seen Powr/Door fixtures.  The repairman could go out and find almost anything up on the pole, so a complete replacement fixture would be more practical.
Logged

01010010 01101111 01100010 01100101 01110010 01110100

streetlight98
Member
*****
Offline

Gender: Male
View Posts
View Gallery

Mike McCann


GoL Mike McCann 88219189@N04/albums
WWW
Re: Why not more POWR/DOOR or PowerPad fixtures « Reply #8 on: June 30, 2016, 10:23:58 AM » Author: streetlight98
We have a huge variety here and we used Powr/Doors. But they never replaced the doors on them. when the fixture failed or it was time for HPS, new fixtures were installed.  We had used M-250As and M-250A2 FCOs. The M-250A2 FCOs all had dual-wattage 100/175W MV ballasts. The fixtures had 240V reactor ballasts with a 120V PC socket. The M-250As were also 240V with 120V PC but they were 100 or 175W single wattage.
Logged

Please check out my newly-updated website! McCann Lighting Company is where my street light collection is displayed in detail.

Print 
© 2005-2024 Lighting-Gallery.net | SMF 2.0.19 | SMF © 2021, Simple Machines | Terms and Policies